Views:

A list of available CLI commands for managing the Service Gateway 1.0 virtual appliance.

To access the CLI, connect to VMware ESXi (either directly or through SSH) and open the Service Gateway virtual appliance. Log on to the CLI with your account credentials.
Note
Note
Make sure you disable the Scroll Lock key on your keyboard when using HyperTerminal.
To view basic information of the Service Gateway, such as network settings and service status, run the show command. For example, use show ipv4 address to check the network address. For a list of available commands, type show and then press the ? key.
To view a list of tasks you can perform and enable administrative commands, run the enable command. Enabling administrative commands changes the command prompt from > to #. The following table lists out the administrative commands you can use to manage the Service Gateway virtual appliance.
Command Syntax Description
configure dns ipv4
configure dns ipv4 <dns1> [dns2]
Configure IPv4 DNS settings
<dns1>: IPv4 address of the primary DNS server
[dns2]: IPv4 address of the secondary DNS server
configure dns ipv6
configure dns ipv6 <dns1> [dns2]
Configure IPv6 DNS settings
<dns1>: IPv6 address of the primary DNS server
[dns2]: IPv4 address of the secondary DNS server
configure dump
configure dump
List commands to recreate configuration on other appliances
configure endpoint
configure endpoint <hostname>
Configure the endpoint name
<hostname>: Endpoint name or FQDN
configure ipv4 cni
configure ipv4 cni <ip> <mask> <gateway> <cni> [vlan]
Configure the default Ethernet interface to use the static IP configuration and setup internal network address pool
<cni>: Internal network address pool (IP address ending in .0.0)
[vlan]: VLAN ID (1-4094)
configure ipv4 static
configure ipv4 static <ip> <mask> <gateway> [vlan]
Configure the default Ethernet interface to use the static IPv4 configuration
[vlan]: VLAN ID (1-4094)
configure ipv6 static
configure ipv6 static <v6ip> <v6mask> <v6gate> [vlan]
Configure the default Ethernet interface to use the static IPv6 configuration
[vlan]: VLAN ID (1-4094)
configure ntp
configure ntp <ip or FQDN>
Configure the NTP server
configure password
configure password
Configure the account password
configure proxy set
configure proxy set <proxy type> <proxy information>
Configure the proxy server for the Service Gateway virtual appliance
<proxy type>: Currently supports http
<proxy information>: Credentials as username:password@IP:port
configure proxy delete
configure proxy delete
Delete proxy settings
configure verify aws
configure verify aws
Verify AWS server configuration
configure verify dns
configure verify dns <domain>
Verify DNS server configuration
<domain>: Domain used to verify DNS server (default: www.google.com)
configure verify ntp
configure verify ntp
Verify NTP server configuration
configure verify dbg
configure verify dbg [cmd] [param] [subparam]
Debug command for configure verify
[cmd]: debug cmd []
[param]: debug param []
[subparam]: debug subparam []
Note
Note
This command typically for support provider use only.
connect
connect
Test connection to Trend Vision One
exit
exit
Exit the CLI
help
help
Display the CLI syntax
history
history [limit]
Display the session's command history
[limit]: The number of CLI commands to display
log
log collect <upload> <local>
Collect Service Gateway debugging data for troubleshooting
<upload>: Upload Service Gateway debugging data to Trend Vision One
<local>: Store Service Gateway debugging data locally
ping
ping <address>
Check the connection to a specific address
reboot
reboot [time]
Restart the Service Gateway after a specified delay or immediately
[time]: Delay in minutes
register
register <regiatration_token>
Register the Service Gateway to Trend Vision One
shutdown
shutdown [time]
Shut down the Service Gateway after a specified delay or immediately
[time]: Delay in minutes
unregister
unregister
Unregister the Service Gateway from Trend Vision One